Reciprocal intronic and exonic histone modification regions in humans.

While much attention has been focused on chromatin at promoters and exons, human genes are mostly composed of intronic sequences. Analyzing published surveys of nucleosomes and 41 chromatin marks in humans, we identified histone modifications specifically associated with 5' intronic sequences, distinguishable from promoter marks and bulk nucleosomes. These intronic marks were spatially reciprocal to trimethylated histone H3 Lys36 (H3K36me3), typically transitioning near internal exons. Several marks transitioned near bona fide exons, but not near nucleosomes at exon-like sequences. Therefore, we examined whether splicing affects histone marking. Even with considerable changes in regulated alternative splicing, histone marks were stable. Notably, these findings are consistent with exon definition influencing histone marks. In summary, we show that the location of many intragenic marks in humans can be distilled into a simple organizing principle: association with 5' intronic or 3' exonic regions

Ionic Polyimides: New High Performance Polymers for Additive Manufacturing

There is currently a very limited set of engineering polymers that have been demonstrated as viable for use in 3-D printing. Additive manufacturing of custom components will require a much larger array of polymers, especially those with physical, thermal, chemical, and mechanical properties that can be tailor-made. The development of Ionic Polyimides offers a solution to this shortage by combining the well understood and widely accepted properties of conventional polyimides, with a new approach to polymer synthesis. Polyimides and polymeric ionic liquids (poly(ILs)) are at the forefront of advanced polymer materials, each with their own set of advantages and disadvantages. While it is clear that more types of polymer materials are needed for fused deposition modeling (FDM) additive manufacturing, there is a need to explore these classes of materials. The synthesis process developed by the Bara Research Group at the University of Alabama allows full control over polymer structure, nanostructure, thermal, electrical, and physical properties making them a prime candidate for use in the additive manufacturing process

New fabrication technique for highly sensitive qPlus sensor with well-defined spring constant

A new technique for the fabrication of highly sensitive qPlus sensor for atomic force microscopy (AFM) is described. Focused ion beam was used to cut then weld onto a bare quartz tuning fork a sharp micro-tip from an electrochemically etched tungsten wire. The resulting qPlus sensor exhibits high resonance frequency and quality factor allowing increased force gradient sensitivity. Its spring constant can be determined precisely which allows accurate quantitative AFM measurements. The sensor is shown to be very stable and could undergo usual UHV tip cleaning including e-beam and field evaporation as well as in-situ STM tip treatment. Preliminary results with STM and AFM atomic resolution imaging at $4.5\,K$ of the silicon $Si(111)-7\times 7$ surface are presented.Comment: 5 pages, 3 figure

Binary Atomic Silicon Logic

It has long been anticipated that the ultimate in miniature circuitry will be crafted of single atoms. Despite many advances made in scanned probe microscopy studies of molecules and atoms on surfaces, challenges with patterning and limited thermal stability have remained. Here we make progress toward those challenges and demonstrate rudimentary circuit elements through the patterning of dangling bonds on a hydrogen terminated silicon surface. Dangling bonds sequester electrons both spatially and energetically in the bulk band gap, circumventing short circuiting by the substrate. We deploy paired dangling bonds occupied by one movable electron to form a binary electronic building block. Inspired by earlier quantum dot-based approaches, binary information is encoded in the electron position allowing demonstration of a binary wire and an OR gate

Integral habitat transport system

In the 1993 Fall quarter, the ME 4182 design class was sponsored to study various scenarios that needed to be studied for Martian travel. The class was sponsored by NASA and there were several different design projects. The design that group three chose was an integral transport system for a Martian habitat. An integral transport system means the design had to be one that was attached to the habitat. There were several criteria that the design had to meet. Group three performed an in depth study of the Martian environment and looked at several different design ideas. The concept group three developed involved the use of kinematic linkages and the use of Martian gravity to move the habitat. The various design concepts, the criteria matrices and all other aspects that helped group three develop their design can be found in their 1993 ME 4182 design report. Now it is Winter quarter 1994 and group three is faced with another problem. The problem is building a working prototype of their Fall design. The limitations this quarter were the parts. The group had to make the prototype work with existing manufactured parts or make the parts themselves in a machine shop. The prototype was scaled down roughly about twelve times smaller than the original design. The following report describes the actions taken by group three to build a working model